Home : 32mm :
I do a lot of built up edges on applied ends, shelves, counters and toe-kicks. I came up with the glue-up fence to speed up/simplify the task. The glue-up fence is made from 2x2" angle iron. It has removable stops on the front edge to space the fence from the edge of the panel and holes in the face to mount the fence. The holes were designed to work with a Vix-bit and screws as well as 5mm pins.
Once the fence is screwed in place the stops are removed. While you could use clamps to hold the fence in place (and that's what I do for shelves where I don't want holes), its easier to do the glue-up with nothing in the way at the front of the fence.
Since I was putting holes in the panels I decided to put them someplace useful. I decided on two rows of holes spaced 32mm apart. The primary row is 37mm from the front edge of the fence to match 32mm system holes. I use the system row to index the Modeez brackets that I use to mount my applied ends. The second row is 9.5mm (22.5 would also be useful) from the front of the fence and is used to mount the Modeez bracket in a horizontal position for applied ends that butt to the ceiling and toe-kick trim.
The fence stops set the fence back 21mm (19mm faces + 2mm bumpers) from the edge. If the applied end is made side panel depth plus 44mm (21 x 2), the fence can be used to drill the front and back Modeez mounting holes. After the panel is glued the banding thickness is ripped off the front edge (clean edge plus edgebanding = 21mm deep buildup). I use 6mm applied backs which leaves 15mm (21 - 6) for scribing the back edge to the wall. That's a bit generous but it simplifies things. You could also make a 1/4" panel sized template with 1/4" holes (for Vix-bit) where the Modeez mounting holes need to be.
[ comment | link | top ]
Tools
Tape Measures
It appears that all FastCap (standard/) metric tapes have 32mm increment marks. I favor the PMMR-Flat16 FlatBack for layout. I also use the PMMR-True32 ProCarpenter. I have yet to try the Standard/Metric Peel & Stick 16' Tape (PMS-Stick16).
[ comment | link | top ]
[ comment | link | top ]
Glue-up fence
I do a lot of built up edges on applied ends, shelves, counters and toe-kicks. I came up with the glue-up fence to speed up/simplify the task. The glue-up fence is made from 2x2" angle iron. It has removable stops on the front edge to space the fence from the edge of the panel and holes in the face to mount the fence. The holes were designed to work with a Vix-bit and screws as well as 5mm pins.
Once the fence is screwed in place the stops are removed. While you could use clamps to hold the fence in place (and that's what I do for shelves where I don't want holes), its easier to do the glue-up with nothing in the way at the front of the fence. 
Since I was putting holes in the panels I decided to put them someplace useful. I decided on two rows of holes spaced 32mm apart. The primary row is 37mm from the front edge of the fence to match 32mm system holes. I use the system row to index the Modeez brackets that I use to mount my applied ends. The second row is 9.5mm (22.5 would also be useful) from the front of the fence and is used to mount the Modeez bracket in a horizontal position for applied ends that butt to the ceiling and toe-kick trim. The fence stops set the fence back 21mm (19mm faces + 2mm bumpers) from the edge. If the applied end is made side panel depth plus 44mm (21 x 2), the fence can be used to drill the front and back Modeez mounting holes. After the panel is glued the banding thickness is ripped off the front edge (clean edge plus edgebanding = 21mm deep buildup). I use 6mm applied backs which leaves 15mm (21 - 6) for scribing the back edge to the wall. That's a bit generous but it simplifies things. You could also make a 1/4" panel sized template with 1/4" holes (for Vix-bit) where the Modeez mounting holes need to be.
[ comment | link | top ]